machine en origine de cycle

English translation: machine in cycle start position

GLOSSARY ENTRY (DERIVED FROM QUESTION BELOW)
French term or phrase:machine en origine de cycle
English translation:machine in cycle start position
Entered by: pooja_chic

17:57 Dec 26, 2012
French to English translations [PRO]
Tech/Engineering - Automation & Robotics
French term or phrase: machine en origine de cycle
OUVERTURE
PORTE Bouton poussoir lumineux vert
Le bouton poussoir permet l'arrêt du cycle continu de la machine en origine de cycle.
Le voyant est allumé fixe lorsque l’autorisation d’ouverture est accordée (Arrêt cycle). Il clignote pour indiquer la prise en compte de la demande après appui sur le bouton poussoir.
En cours de cycle le voyant est éteint.
pooja_chic
machine in cycle start position
Explanation:
The question may refer either to several machines in line connected to one cycle or, more probably, to a machine cycle. That cycle starts, acts and restatrs again after finishing the cylce.

Prcessing time variations: The cycle time is the time required for a single operation.
:
Synchronous line: A production line, where cycle time is deterministic and identical, and operations start and stops together.
:http://dspace.mit.edu/bitstream/handle/1721.1/30338/61126370...

The machine cycle is programmed for fully automatic sequencing from drilling feed and speed to countersinking feed, speed, and dwell time, then tapping cycles.
http://www.accmach.com/case-studies/drill-tap-machine/

12.7 Single-Station Automated Cells
The single-station automated cell consists of a fully automated machine that can operate unattended for a time period longer than one machine cycle.
http://www.nuigalway.ie/staff-sites/david_osullivan/document...

Machine time (unten jikan): The time from machine cycle start switch on, through processing, to the machine then returning to it’s original starting position, during which time there is no hands-on work by the operator.
http://www.jmac-america.com/vocabulary.htm

Referring again to FIG. 3, the next section of the process configuration screen 124 allows the operator to enter the cycle start, stop, abort and delta deadband information. Here, the operator enters the starting and ending PLC addresses for the cycle time along with the off/on condition for the cycle start, stop, and abort configurations.
http://www.patentopedia.us/molded_rubber_base_luggage/cycle_...

... both the ifrard sensoer an teh location sensor must be satisfied in order to energize a mechanical relay to send a cycle start signal to the machine.
:
The two-hand operating lever, trip, or control device shall require concurrent actuation of both of the operating levers or hand controls to initiate a machine cycle.
http://www.pinnaclesystems.com/Brochure-PDFs/ultratouch.pdf

Machine cycle start is caused by simple pressing of two “start” buttons (to be pressed at same time) placed on machine base.
http://europackinternational.com/product.php?id_product=33
Selected response from:

Johannes Gleim
Local time: 10:20
Grading comment
Thank you so much.
4 KudoZ points were awarded for this answer



Summary of answers provided
4 +1machine in cycle start position
Johannes Gleim
3at the beginning of the cycle
cc in nyc
5 -3Machine to restart
Salih YILDIRIM


Discussion entries: 3





  

Answers


35 mins   confidence: Answerer confidence 4/5Answerer confidence 4/5 peer agreement (net): +1
machine in cycle start position


Explanation:
The question may refer either to several machines in line connected to one cycle or, more probably, to a machine cycle. That cycle starts, acts and restatrs again after finishing the cylce.

Prcessing time variations: The cycle time is the time required for a single operation.
:
Synchronous line: A production line, where cycle time is deterministic and identical, and operations start and stops together.
:http://dspace.mit.edu/bitstream/handle/1721.1/30338/61126370...

The machine cycle is programmed for fully automatic sequencing from drilling feed and speed to countersinking feed, speed, and dwell time, then tapping cycles.
http://www.accmach.com/case-studies/drill-tap-machine/

12.7 Single-Station Automated Cells
The single-station automated cell consists of a fully automated machine that can operate unattended for a time period longer than one machine cycle.
http://www.nuigalway.ie/staff-sites/david_osullivan/document...

Machine time (unten jikan): The time from machine cycle start switch on, through processing, to the machine then returning to it’s original starting position, during which time there is no hands-on work by the operator.
http://www.jmac-america.com/vocabulary.htm

Referring again to FIG. 3, the next section of the process configuration screen 124 allows the operator to enter the cycle start, stop, abort and delta deadband information. Here, the operator enters the starting and ending PLC addresses for the cycle time along with the off/on condition for the cycle start, stop, and abort configurations.
http://www.patentopedia.us/molded_rubber_base_luggage/cycle_...

... both the ifrard sensoer an teh location sensor must be satisfied in order to energize a mechanical relay to send a cycle start signal to the machine.
:
The two-hand operating lever, trip, or control device shall require concurrent actuation of both of the operating levers or hand controls to initiate a machine cycle.
http://www.pinnaclesystems.com/Brochure-PDFs/ultratouch.pdf

Machine cycle start is caused by simple pressing of two “start” buttons (to be pressed at same time) placed on machine base.
http://europackinternational.com/product.php?id_product=33

Johannes Gleim
Local time: 10:20
Works in field
Native speaker of: German
PRO pts in category: 8
Grading comment
Thank you so much.

Peer comments on this answer (and responses from the answerer)
agree  Tony M: Yes, my understanding is that it stops the machine and puts if back to the start position, thus allowing safe opening of the door.
15 hrs
  -> That's what I thought, too! Thanks!
Login to enter a peer comment (or grade)

2 hrs   confidence: Answerer confidence 3/5Answerer confidence 3/5
en origine de cycle
at the beginning of the cycle


Explanation:
So, for "permet l'arrêt du cycle continu de la machine en origine de cycle," perhaps something like "allows stopping the machine's continuous cycle at the beginning of the cycle" – which might be shortened, perhaps, to "stops/interrupts the machine's operation at the beginning of the cycle."

--------------------------------------------------
Note added at 7 hrs (2012-12-27 01:18:28 GMT)
--------------------------------------------------

Or maybe rephrase:

"The [illuminated] button can be pressed at the beginning of the cycle to stop the machine's continuous operation."

cc in nyc
Local time: 05:20
Native speaker of: English
PRO pts in category: 4

Peer comments on this answer (and responses from the answerer)
neutral  Tony M: I don't think it means you can only press it at the beginning (otherwise, how can you stop it later?) — I think JG has it right, it stops the machine and moves it back to the start position. 'arrêt en XXX' is often used in this sort of way in FR.
12 hrs
  -> In fact my thought was that the cycle cannot be stopped later. But that could be wrong. ;-)
Login to enter a peer comment (or grade)

1 hr   confidence: Answerer confidence 5/5 peer agreement (net): -3
Machine to restart


Explanation:
Imho

--------------------------------------------------
Note added at 21 hrs (2012-12-27 14:57:45 GMT)
--------------------------------------------------

The Best Trio on STAGE!!!

Salih YILDIRIM
United States
Local time: 05:20
Native speaker of: Native in TurkishTurkish
PRO pts in category: 3

Peer comments on this answer (and responses from the answerer)
disagree  Kim Metzger: What about "origine de cycle"?
1 hr

disagree  Tony M: 'en origine' hardly indicates 'to restart'
14 hrs
  -> Check Proz's response if you don't mind!

disagree  Cetacea: "to restart" has nothing to do with "en origine de cycle".
15 hrs
  -> Check Proz's response if you don't mind!
Login to enter a peer comment (or grade)



Login or register (free and only takes a few minutes) to participate in this question.

You will also have access to many other tools and opportunities designed for those who have language-related jobs (or are passionate about them). Participation is free and the site has a strict confidentiality policy.

KudoZ™ translation help

The KudoZ network provides a framework for translators and others to assist each other with translations or explanations of terms and short phrases.


See also:
Term search
  • All of ProZ.com
  • Term search
  • Jobs
  • Forums
  • Multiple search