Glossary entry (derived from question below)
English term or phrase:
stock tube
Italian translation:
tubo (della testa / di alimentazione barra)
Added to glossary by
martini
Feb 18, 2022 11:15
2 yrs ago
15 viewers *
English term
stock tube
English to Italian
Tech/Engineering
Engineering (general)
TORNIO
Spindle breaking:
The spindle or workpiece should never be slowed or stopped by hand gripping or any other means.
Always use the machine controls to stop or slow it.
Workpieces extending out of the lathe should be supported by a ***stock tube***:
If a slender workpiece is allowed to extend beyond the headstock spindle a foot or so without support, it can fly outward from centrifugal force.
PREMETTO
Che il documento è scritto molto bene e la terminologia tecnica è perfetta
RIFERIMENTI
Ho trovato un solo documento che descrive questo elemento
Pagina 76 immagine
Pagina 77 descrizione
https://www.kdkce.edu.in/upload//Lathe Machine.pdf
Faccio presente che il dizionario come lemma "tube stock" tratta altra cosa
Grazie per un qualsiasi aiuto
Spindle breaking:
The spindle or workpiece should never be slowed or stopped by hand gripping or any other means.
Always use the machine controls to stop or slow it.
Workpieces extending out of the lathe should be supported by a ***stock tube***:
If a slender workpiece is allowed to extend beyond the headstock spindle a foot or so without support, it can fly outward from centrifugal force.
PREMETTO
Che il documento è scritto molto bene e la terminologia tecnica è perfetta
RIFERIMENTI
Ho trovato un solo documento che descrive questo elemento
Pagina 76 immagine
Pagina 77 descrizione
https://www.kdkce.edu.in/upload//Lathe Machine.pdf
Faccio presente che il dizionario come lemma "tube stock" tratta altra cosa
Grazie per un qualsiasi aiuto
Proposed translations
(Italian)
3 | tubo (della testa / di alimentazione barra) | martini |
3 | tubo guida | Francesco Badolato |
Change log
Feb 19, 2022 15:14: martini Created KOG entry
Proposed translations
2 hrs
Selected
tubo (della testa / di alimentazione barra)
Anche l'alimentazione della barra necessaria per ogni pezzo avviene in automatico, da una lunga barra che viene inserita attraverso un tubo che ha la testata e viene trattenuta tramite pinze idrauliche di bloccaggio.
https://www.olivertools.com/news/storia-e-tipologie-del-torn...
dal tuo pdf
Bar stock is pushed through stock tube in a bracket & its leading end is
clamped in rotating spindle by means of collet chuck.
The machine operator must go to the front of the machine, remove the bar end (remnant) and discard it, and then go to the back of the machine and load a fresh bar into the stock tube. Loading the fresh bar is no easy task: he must guide it through the bar tube's compression springs and literally pound it through the bar feeder collet to the stock stop.
It takes the operator 6 to 8 minutes to load fresh bars into the stock tubes,"
https://www.mmsonline.com/articles/choosing-the-right-bar-fe...
https://www.olivertools.com/news/storia-e-tipologie-del-torn...
dal tuo pdf
Bar stock is pushed through stock tube in a bracket & its leading end is
clamped in rotating spindle by means of collet chuck.
The machine operator must go to the front of the machine, remove the bar end (remnant) and discard it, and then go to the back of the machine and load a fresh bar into the stock tube. Loading the fresh bar is no easy task: he must guide it through the bar tube's compression springs and literally pound it through the bar feeder collet to the stock stop.
It takes the operator 6 to 8 minutes to load fresh bars into the stock tubes,"
https://www.mmsonline.com/articles/choosing-the-right-bar-fe...
Note from asker:
Ciao. Ti ringrazio per i riferimenti che sono serviti per capire che era corretta la mia prima ipotesi. Il link da me fornito e i tuoi riferimenti per stock tube non sono applicabili alla configurazione del tornio in questione e sono serviti per capire la corretta interpretazione. Il mio testo parla semplicemente che se dalla testa del mandrino il tubo si estende oltre 30 cm deve essere supportato (dalla controtesta). Tutt'altro discorso dell'altra situazione, la mia controtesta è diversa. Con le indicazioni fornite ho trovato un video e sono sicuro al 100%. Grazie dell'aiuto e buon lavoro |
4 KudoZ points awarded for this answer.
Comment: "Grazie"
4 hrs
tubo guida
Mi è capitato di tradurre i due termini in questo modo ma non so se va bene per
questo contesto.
Confidence medio.
--------------------------------------------------
Note added at 6 ore (2022-02-18 17:53:25 GMT)
--------------------------------------------------
Figurati e buon lavoro anche da parte mia.
questo contesto.
Confidence medio.
--------------------------------------------------
Note added at 6 ore (2022-02-18 17:53:25 GMT)
--------------------------------------------------
Figurati e buon lavoro anche da parte mia.
Note from asker:
Ciao Francesco. Grazie e buon lavoro |
Discussion
Mi sfugge qualcosa?